Utility pole specifications and standards: a buyer’s guide

A utility pole specification names the pole (length, class, and species or material), the standard it is made to, how it is treated or finished, how it is framed, and how it is inspected. In the US, four sets of documents sit behind almost every pole spec: ANSI O5.1 for wood pole dimensions, the National Electrical Safety Code (NESC) for loading and strength, AWPA standards for preservative treatment, and USDA Rural Utilities Service (RUS) bulletins for federally financed co-ops.

On Sourcewell Contract #060326-BIDR: wood poles 25 to 70 ft, Class 1 to 5, plus galvanized steel, spun concrete and composite poles, delivered across the contiguous US.

Utility pole standards at a glance

Which document governs which part of a pole purchase.

StandardPublished byWhat it governs
ANSI O5.1-2022, Wood Poles: Specifications and DimensionsAccredited Standards Committee O5; the American Wood Protection Association is its secretariatMinimum quality and dimensions of wood poles: species, class, length, circumference and fiber strength
National Electrical Safety Code (IEEE C2-2023)IEEE, every five yearsLoads a line must withstand (ice, wind, temperature), grades of construction, and load and strength factors
AWPA U1 and T1American Wood Protection AssociationWhich preservatives and how much (U1, the Use Category System); how the wood is processed and treated (T1)
RUS bulletins, such as 1728F-700USDA Rural Utilities ServicePurchase specifications and design guides that RUS electric borrowers follow
ASCE/SEI 48-19, Design of Steel Transmission Pole StructuresAmerican Society of Civil EngineersDesign, fabrication, testing and erection of tubular steel poles
ASTM C1089ASTM InternationalSpun cast prestressed concrete poles
ASCE Manual of Practice 104 (second edition, 2019)American Society of Civil EngineersRecommended practice for fiber-reinforced polymer (FRP) poles and crossarms
General Order 95California Public Utilities CommissionOverhead line construction in California, in place of the NESC

The NESC is a voluntary standard that states adopt into law. Florida and Michigan, for example, have adopted the 2023 edition by rule. The 2023 edition took effect on February 1, 2023. Check which edition your state or utility commission has adopted before you cite it in a specification.

What a pole specification or data sheet lists

The fields that show up in federal and utility pole purchase specifications.

These fields come from three published specifications: RUS Bulletin 1728F-700 (the federal wood pole specification), Snohomish County PUD’s wood pole material standard, and Eugene Water & Electric Board’s wood pole specification. Each field below appears in at least two of the three.

FieldWhat to stateWhere it comes from
Length and classFor example, 45 ft Class 3. Length is in 5 ft steps.ANSI O5.1. See the size charts.
Species or materialSouthern Pine, Douglas Fir, Western Red Cedar; or steel, concrete or compositeANSI O5.1 for wood species
Governing standard and editionThe standard the pole must meet, with its yearANSI O5.1 for wood; ASCE 48, ASTM C1089 or ASCE MOP 104 for other materials
PreservativeCCA, creosote, copper naphthenate, DCOI or another accepted typeAWPA U1
Retention and penetrationPounds of preservative per cubic foot, and how deep it reachesAWPA U1 and T1; RUS Bulletin 1728F-700, Table 8
Use categoryUC4A, UC4B or UC4C for poles in the groundAWPA U1
ConditioningHow the pole is seasoned or sterilized before treatmentAWPA T1; the utility’s own spec
FramingHoles, gains and cuts, made before treatmentThe utility’s framing drawing
MarkingBrand or tag with treater, plant, date, species, preservative, class and lengthRUS Bulletin 1728F-700; ANSI O5.1
InspectionA quality assurance plan or an independent inspection agencyRUS Bulletin 1728F-700
Delivery and handlingSite, unloading, and limits on damage in transitThe utility’s own spec
Rejection and warrantyWhat makes a pole rejectable, and for how longThe utility’s own spec

Two details are easy to miss. First, framing is done before treatment: RUS says poles should be bored, gained and cut to length before final treatment, and Snohomish County PUD requires all gains cut and holes bored before poles are treated. Second, RUS limits storage time: no pole may be shipped to an RUS borrower more than two years after its original treatment date.

For steel and concrete poles, RUS’s guide specification lists the order details as pole length, pole class, pole framing (attachment requirements) and embedment depth. The maker then supplies a drawing with diameters, wall thickness and weight.

Pole loading standards: NESC loading districts

The ice, wind and temperature a line must be designed for.

The NESC sets the loads an overhead line must withstand. Rule 250B divides the mainland US into three loading districts: heavy, medium and light. Each district pairs a thickness of ice on the wires with a wind pressure and a temperature.

DistrictRadial ice on wires (in)Wind pressure (lb per sq ft)Temperature (°F)
Heavy0.5040
Medium0.25415
LightNone930

These values are as reproduced in RUS Bulletin 1724E-200 (from the 2012 NESC) and by the North American Wood Pole Council (from the 2017 NESC). RUS also lists a fourth row, Warm Islands, with no ice and a 9 lb per sq ft wind at 50 °F up to 9,000 ft elevation. Austin Energy’s February 2026 pole loading guidelines still use the medium district values.

Extreme wind and extreme ice

Two more load cases apply to taller structures. Rule 250C covers extreme wind, and Rule 250D covers extreme ice with concurrent wind. RUS and utility documents describe both as applying when a structure or the wires it carries are more than 60 ft above ground. RUS recommends that all transmission lines meet the extreme wind case regardless of height. The 2023 NESC updated the wind maps behind these rules, so use the maps in the edition your state has adopted.

Grades of construction

The NESC sets three grades of construction. Grade B is the strongest and is used where a line crosses limited-access highways, railroads or navigable waterways. Grade C is the usual grade for distribution poles. Grade N is the lowest. Federal rules require RUS borrowers to build distribution lines to at least Grade C and transmission lines to at least Grade B. Austin Energy runs distribution poles at Grade B for major road crossings and Grade C elsewhere.

Load factors and strength factors

A design multiplies each load by a load factor and multiplies the pole’s strength by a strength factor. The pole passes when its factored strength is at least the factored load. For the district loading case:

FactorGrade BGrade C
Wood pole strength factor0.650.85
Steel, prestressed concrete and FRP pole strength factor1.001.00
Load factor, transverse wind2.501.75
Load factor, wire tension1.651.30
Load factor, vertical1.501.90

These factors are as published by the North American Wood Pole Council from the 2017 NESC, and the Grade B column matches RUS Bulletin 1724E-200. Under the 2017 code, the Grade C wind factor rises to 2.20 at crossings. Under the extreme wind and extreme ice cases, the wood strength factor is 0.75.

The different strength factors are why a steel, concrete or composite pole sold as “equivalent” to a wood class needs a check. RUS warns that the owner must be sure the strength factors are properly accounted for in the design of steel poles. The North American Wood Pole Council, the wood pole trade group, goes further and argues there can be no true wood-equivalent pole.

Wood pole specifications: ANSI O5.1

Class, dimensions and fiber strength.

ANSI O5.1 sets minimum specifications for the quality and dimensions of wood poles used as single-pole utility structures. It classifies poles by species, length and class. A class is a strength rating: every pole in a class can hold the same horizontal load applied 2 ft from the top. A Class 4 pole holds 2,400 lb and a Class 3 pole holds 3,000 lb, and each class is about 25% stronger than the one below it.

To give each species the same strength in a class, the standard assigns each one a fiber strength. Weaker species get larger minimum circumferences.

SpeciesDesignated fiber strength (psi)
Western Larch8,400
Southern Pine8,000
Douglas Fir8,000
Lodgepole Pine, Red Pine, Jack Pine6,600
Ponderosa Pine6,000
Western Red Cedar6,000
Northern White Cedar4,000

These values are from RUS Bulletin 1724E-200 and the North American Wood Pole Council, which reproduce the 2008 and 2015 editions of ANSI O5.1. The standard also limits defects such as knots, checks and sweep. For circumference and diameter by length and class, see the utility pole size charts. For species and service life, see the wood utility pole guide.

Treatment specifications: AWPA use categories and retention

How a spec says what the pole is treated with, and how much.

AWPA Standard U1 sorts treated wood into use categories by exposure. Utility poles fall in Use Category 4, ground contact. The category depends on how severe decay is where the pole will stand.

Use categoryExposurePoles it covers
UC4AGround contact, general usePoles in regions with low natural potential for decay and insect attack
UC4BGround contact, heavy dutyPoles in moist temperate climates
UC4CGround contact, extreme dutyPoles in semi-tropical or tropical environments

Retention is the amount of preservative left in the wood, in pounds per cubic foot. RUS Bulletin 1728F-700 (April 18, 2022) publishes minimum retentions for RUS borrowers:

Species and use areaCreosoteDCOIWaterborneCopper naphthenate
Southern Pine, area 19.00.150.600.130
Southern Pine, area 27.50.13–0.080
Douglas Fir, area 112.00.200.600.150
Douglas Fir, area 29.00.15–0.095
Western Red Cedar, area 220.00.330.600.120

Use area 1 is the Southeast: south of the 40th parallel and east of the 95th meridian, including the Gulf Coast of Texas. The table also has a pentachlorophenol column, left out here because EPA has cancelled penta: production and sale ended February 29, 2024, and treating plants may use existing stock only until February 28, 2027. The wood pole guide covers each preservative.

An older 2019 copy of Bulletin 1728F-700 is still online with lower copper naphthenate figures and no DCOI column. Cite the April 18, 2022 edition.

RUS bulletins for pole buyers

The federal specifications electric co-ops with RUS loans follow.

The USDA Rural Utilities Service lends to rural electric systems, and its borrowers must follow its specifications. Under 7 CFR 1728, borrowers purchase only materials on the RUS List of Materials or with current technical acceptance from RUS. Many utilities that are not RUS borrowers cite the same bulletins because they are free and detailed.

BulletinTitleDate
1728F-700 (opens in a new tab)RUS Specification for Wood Poles, Stubs and Anchor LogsApril 2022
1724E-150 (opens in a new tab)Unguyed Distribution Poles: Strength RequirementsAugust 2014
1724E-200 (opens in a new tab)Design Manual for High Voltage Transmission LinesDecember 2015
1724E-204 (opens in a new tab)Guide Specifications for Steel Single Pole and H-Frame StructuresApril 2019
1724E-214 (opens in a new tab)Guide Specification for Standard Class Steel Transmission PolesApril 2019
1724E-206 (opens in a new tab)Guide Specification for Prestressed Concrete Poles and Concrete Pole StructuresAugust 2016
1724E-216 (opens in a new tab)Guide Specification for Standard Class Prestressed Concrete Transmission PolesJuly 2016
1728F-804 (opens in a new tab)Specifications and Drawings for 12.47/7.2 kV Line Construction2005

Bulletin 1728F-700 is the one that binds a wood pole purchase: each RUS borrower must purchase only wood poles produced to it. It offers two purchase plans. Under the quality assurance plan, the producer’s own program covers the poles. Under the independent inspection plan, a qualified inspector checks every pole. The 2022 edition still cites the 2017 edition of ANSI O5.1.

Steel, concrete and composite pole specifications

The standards a spec cites when the pole is not wood.

Steel

RUS requires steel transmission poles to be designed to ASCE 48, Design of Steel Transmission Pole Structures; the current edition is ASCE/SEI 48-19. RUS’s guide specification accepts steel to ASTM A36, A572, A588, A871 or A595. Galvanized poles must meet ASTM A123 or A153. Weathering steel, which forms its own protective oxide layer, is steel to ASTM A588 or A871, and RUS says A588 poles are not to be galvanized. Standard class steel poles are rated by a tip load applied 2 ft from the top, the same point used for wood classes.

Concrete

ASTM C1089 is the specification for spun cast prestressed concrete poles used for lighting, traffic signals, and transmission, distribution and communication lines. RUS also cites ASTM C935 for statically cast poles and the ASCE/PCI Guide for the Design of Prestressed Concrete Poles. RUS’s standard classes for concrete poles are rated by tip load in the same way as steel.

Composite

ASCE Manual of Practice 104, Recommended Practice for Fiber-Reinforced Polymer Products for Overhead Utility Line Structures (second edition, 2019), covers FRP poles and crossarms and recommends performance-based tests. Two documents sometimes cited for composite poles do not fit utility line poles: ANSI C136.20 applies to lighting poles for roadways and areas, and ASTM D4923, a lighting pole specification, was withdrawn in 2010.

Each material has its own guide: steel, concrete and fiberglass and composite. To compare all four, see types of utility poles.

Pole loading analysis

The calculation that shows a pole can carry what is attached to it.

A pole loading analysis works out the wind and ice loads on a pole and everything attached to it, then compares them with the pole’s strength. Nashville Electric Service describes it as wind and ice loading calculations to determine the structural capacity of the pole.

Pole owners usually require one before a new attachment goes on. Nashville Electric Service requires a pole loading analysis by a licensed professional engineer as part of its pre-construction survey. Austin Energy requires one for poles with five or more existing communication attachments and reserves the right to require one on any pole; total usage must come in under 90% of the pole’s groundline moment capacity.

Terms in a pole loading report

TermMeaning
Groundline momentA load multiplied by its height above the ground line. The pole’s permitted moment at the ground line must equal or exceed the total applied moment.
Wind span (horizontal span)The horizontal distance between the mid-span points of the two adjacent spans. It sets the wind load the pole takes from the wires.
Weight span (vertical span)The horizontal distance between the low points of the sag curves in the two adjacent spans. It sets the wire weight the pole carries.
Strength factorThe share of the pole’s rated strength the NESC lets a design count on: 0.65 for wood at Grade B, 0.85 at Grade C.

As a reference point, the North American Wood Pole Council gives the groundline moment capacity of a 40 ft Class 4 wood pole as 76,800 ft-lb. Utilities name the software they accept: Austin Energy permits O-Calc Pro, and Nashville Electric Service asks for a SPIDAcalc file. The analyst starts from the pole’s brand, which gives length, class and species.

How to read a pole brand

The mark on a wood pole is a short form of its specification.

RUS Bulletin 1728F-700 requires each pole to be burn branded, or fitted with a metal tag, showing the treater, the plant and the month and year of treatment, code letters for species, preservative and retention, and the class and length. The brand sits 10 ft from the butt on poles 50 ft and shorter, and 14 ft from the butt on poles 55 ft and longer, so it can be read at about eye level once the pole is set. Class and length are also marked on the butt.

RUS gives this example:

Line on the brandMeaning
HRLTreater’s code or trademark
S5-08Plant location, month and year of treatment
SPC-9Southern Pine, creosote, 9 lb retention
5-35Class 5, 35 ft

Other code letters in the bulletin include DF for Douglas Fir and WC for Western Red Cedar. Utilities outside the RUS program set their own marking rules; Snohomish County PUD, for example, marks each pole with two aluminum or stainless steel discs.

Buy American rules on federally funded pole purchases

Two rules buyers ask about, and where each applies.

RUS loans. Under 7 CFR 1787, RUS borrowers use loan funds only for manufactured articles, materials and supplies made in the United States or an eligible country, to the extent practicable and where the cost is not unreasonable. A product counts as domestic when domestic components make up more than 50% of its component cost. Compliance is certified on RUS Form 213.

FEMA grants. The Build America, Buy America Act applies to covered FEMA awards issued on or after January 2, 2023, and requires iron, steel, manufactured products and construction materials to be produced in the United States. FEMA lists Building Resilient Infrastructure and Communities among the covered programs. It lists Public Assistance and the Hazard Mitigation Grant Program, the programs most storm repairs run through, as not subject to the Act.

If federal money is paying for the poles, say so in the quote request and name the program, so the origin of the poles can be stated on the quote. Your grant administrator decides which rule applies.

Sending a pole specification for a Sourcewell quote

On Sourcewell Contract #060326-BIDR, BIDR Technologies supplies wood poles 25 to 70 ft in 5 ft steps, Class 1 to Class 5, in Southern Yellow Pine, Douglas Fir and Ponderosa Pine. The BIDR Utilities catalog (opens in a new tab) lists 450 pole specifications, including galvanized steel, spun concrete and composite poles, plus crossarms and line hardware. Pole loading analysis is offered as an engineering service.

If your agency has a written pole specification, attach it to the quote request. If it does not, these are enough to price a wood pole order:

  1. Length and class of each pole, and the quantity of each.
  2. Species, if you have a preference.
  3. Preservative and, if your standard sets one, the retention or AWPA use category.
  4. Framing drawing, or “unframed”.
  5. Any inspection requirement, and any federal funding rule that applies.
  6. Delivery site and need date.

Send them through the utility pole quote form. Your agency stays responsible for its own due diligence. Related guides: utility pole cost and cooperative contracts.

Questions buyers ask

What is the industry standard for wood utility poles?

ANSI O5.1, Wood Poles: Specifications and Dimensions. The current edition is O5.1-2022. It sets species, classes, minimum dimensions and fiber strength. Treatment is specified separately under AWPA U1 and T1, and line loading under the NESC.

What should a utility pole data sheet include?

Length and class, species or material, the governing standard and its edition, preservative with retention and use category, framing, marking, and inspection. For steel, concrete and composite poles, the maker’s drawing adds diameters, wall thickness and weight.

What is the difference between NESC Grade B and Grade C?

Grade B is the stronger grade, used where lines cross limited-access highways, railroads or navigable waterways. Grade C is the usual grade for distribution. For wood poles the strength factor is 0.65 at Grade B and 0.85 at Grade C, so a Grade B design counts on less of the pole’s rated strength.

What are the NESC loading districts?

Heavy, medium and light. Heavy is 0.50 in of radial ice with a 4 lb per sq ft wind at 0 °F. Medium is 0.25 in of ice with the same wind at 15 °F. Light is no ice with a 9 lb per sq ft wind at 30 °F.

Do steel and composite poles follow ANSI O5.1?

No. ANSI O5.1 covers wood only. Steel poles are designed to ASCE 48, spun concrete poles are made to ASTM C1089, and composite poles follow ASCE Manual of Practice 104. They are often ordered by wood-equivalent class, with the strength factors checked.

Does every utility have to follow RUS bulletins?

No. RUS bulletins bind borrowers of the USDA Rural Utilities Service, which are mostly rural electric cooperatives. Other utilities often cite them by choice. Municipal and investor-owned utilities follow the NESC edition their state has adopted and their own construction standards.

Get contract pricing on utility poles

Send your pole specification, or just length, class, material, quantity and delivery site. You get a written quote at Sourcewell contract pricing with a delivery timeline.

Sources

  1. IEEE C2-2023: 2023 National Electrical Safety Code (NESC) (opens in a new tab), IEEE Standards Association
  2. NESC overview (opens in a new tab), IEEE Standards Association
  3. New National Electrical Safety Code to go into effect in February (opens in a new tab), American Public Power Association
  4. Highlights of the new 2023 National Electrical Safety Code (opens in a new tab), EC&M
  5. Florida Administrative Code Rule 25-6.0345 (opens in a new tab), Legal Information Institute, Cornell Law School
  6. Michigan Administrative Code R 460.813 (opens in a new tab), Legal Information Institute, Cornell Law School
  7. Southern California Edison petition on General Order 95 (March 2024) (opens in a new tab), California Public Utilities Commission
  8. General Order 95: Rules for Overhead Electric Line Construction (opens in a new tab), California Public Utilities Commission
  9. RUS Bulletin 1724E-200: Design Manual for High Voltage Transmission Lines (Tables 11-1, 11-6, 11-7 and 13-1; chapter 7) (opens in a new tab), USDA Rural Utilities Service
  10. RUS Bulletin 1724E-150: Unguyed Distribution Poles, Strength Requirements (opens in a new tab), USDA Rural Utilities Service
  11. RUS Bulletin 1728F-700: RUS Specification for Wood Poles, Stubs and Anchor Logs (April 18, 2022) (opens in a new tab), USDA Rural Utilities Service
  12. RUS Bulletin 1724E-204: Guide Specifications for Steel Single Pole and H-Frame Structures (opens in a new tab), USDA Rural Utilities Service
  13. RUS Bulletin 1724E-214: Guide Specification for Standard Class Steel Transmission Poles (opens in a new tab), USDA Rural Utilities Service
  14. RUS Bulletin 1724E-206: Guide Specification for Prestressed Concrete Poles and Concrete Pole Structures (opens in a new tab), USDA Rural Utilities Service
  15. RUS Bulletin 1724E-216: Guide Specification for Standard Class Prestressed Concrete Transmission Poles (opens in a new tab), USDA Rural Utilities Service
  16. RUS Bulletin 1728F-804: Specifications and Drawings for 12.47/7.2 kV Line Construction (opens in a new tab), USDA Rural Utilities Service
  17. RUS bulletin index (opens in a new tab), USDA Rural Development
  18. 7 CFR 1724.50: Compliance with National Electrical Safety Code (opens in a new tab), Electronic Code of Federal Regulations
  19. 7 CFR Part 1728: Electric Standards and Specifications for Materials and Construction (opens in a new tab), Electronic Code of Federal Regulations
  20. 7 CFR Part 1787: The “Buy American” Requirement (opens in a new tab), Electronic Code of Federal Regulations
  21. Technical Bulletin 17-D-202 (NESC loading tables, fiber strength, load and strength factors) (opens in a new tab), North American Wood Pole Council
  22. Technical Bulletin 17-D-201 (wood pole equivalents, class loads, groundline moment) (opens in a new tab), North American Wood Pole Council
  23. ANSI O5.1-2022: Wood Poles, Specifications and Dimensions (catalog page) (opens in a new tab), ANSI Webstore
  24. Accredited Standards Committee O5 (opens in a new tab), ASC O5
  25. Standard U1-25, Use Category System: User Specification for Treated Wood (excerpt) (opens in a new tab), American Wood Protection Association
  26. Pentachlorophenol (opens in a new tab), US Environmental Protection Agency
  27. Design of Steel Transmission Pole Structures (48-19) (catalog page) (opens in a new tab), American Society of Civil Engineers
  28. ASTM C1089: Standard Specification for Spun Cast Prestressed Concrete Poles (catalog page) (opens in a new tab), ASTM International
  29. ASCE MOP 104-2019: Recommended Practice for Fiber-Reinforced Polymer Products for Overhead Utility Line Structures (catalog page) (opens in a new tab), ANSI Webstore
  30. ANSI C136.20-2012 (R2021): Fiber-Reinforced Composite (FRC) Lighting Poles (catalog page) (opens in a new tab), ANSI Webstore
  31. ASTM D4923: Standard Specification for Reinforced Thermosetting Plastic Poles (Withdrawn 2010) (catalog page) (opens in a new tab), ASTM International
  32. Pole Loading Analysis Guidelines, version 1.2 (February 2026) (opens in a new tab), Austin Energy
  33. Pole Attachment and Conduit Usage Guidelines (opens in a new tab), Nashville Electric Service
  34. Discovery response on NESC Rules 250C and 250D (June 2026) (opens in a new tab), Green Mountain Power
  35. NESC grades of construction (opens in a new tab), ikeGPS
  36. Material Standard 897720.2: Full Length Copper Naphthenate Pressure Treated Wood Poles (opens in a new tab), Snohomish County PUD
  37. Material Specification ES4-8.1100: Wood Poles (opens in a new tab), Eugene Water & Electric Board
  38. Build America, Buy America Act (opens in a new tab), FEMA
  39. Programs and definitions: Build America, Buy America Act (opens in a new tab), FEMA
  40. Solicitation 11229: Utility Poles (awarded contracts) (opens in a new tab), Sourcewell
  41. Supply Catalog (opens in a new tab), BIDR Utilities